Keller CTD Sensor
Keller PR-36 XiW CTD Sensor for groundwater monitoring. A Swiss made, latest-generation, multi-parameter sensor, another sensor from Europe’s leading manufacturer of pressure transducers. Available in Stainless Steel or Titanium, the Keller CTD is corrosion proof so delivers extreme accuracy in saline environments. Most importantly the sensor is suitable for level, temperature and conductivity measurements. The sensor is compatible with Van Walt’s telemetry. 30 m of Kevlar Cable is provided with every sensor. Through the sensor’s Modbus interface you can connect a network of sensors. Consequently, you get ultra-high stability for your long-term monitoring with the Keller PR-36 XiW CTD Sensor.
Contact Van WaltAdvantages
- Compatible with Van Walt telemetry (vanwaltCONNECT; vanwaltDataHub & vanwaltDataNode)
- Supplied with 30 m of vented Kevlar Cable so no barometric compensation required
- Available in Stainless Steel or Titanium
- Available from stock with Modbus connection
- High accuracy with resolution of 5 ppm
- Mathematical compensation of nonlinearities and temperature dependencies
- Corrosion proof housing
- Level measuring ranges from 0…3 m to 0…300 m
- Ultra-high long-term stability, particularly for monitoring saline environments
- Devices can be connected together into a network system
- Un-rivalled quality and performance that is synonymous with Swiss engineering.
Keller CTD Sensor Equipment Options:
Applications
- Saltwater intrusion monitoring
- Water quality monitoring for agriculture, remediation and correlation of conductivity with salt, TDS, permanganate, nitrate & sulphate
- Tidal fluctuations monitoring
- Estuary and wetlands monitoring
- Leachate monitoring at landfill sites
- Aquifer storage and recovery
- Network automation monitoring
- Waste Water applications
- Environmental monitoring
- Surface water discharge measurement
- Aquifer storage & recovery
Specifications
(0.3 bar Range: ± 0.04 %FS)
(0.3 bar Range: ± 0.2 %FS)
ranges <e; bar: ± 1 mbar max.
Pt1000 sensor: ± 0.1 °C max.
with extended lightning protection
4.5…32 VDC
without conductivity
with conductivity
< 14 mA (active) 7)
P1, T, Con
3 s typ. 6 s max
0…100 %FS @ 25 °C
KELLER bus
PAA: polyolefin (PE based)
conductivity (additional: titanium, PEEK
EN 61326-1
EN 61326-2-3
Line-CASE: 200 A @ 8/20 μs
1) Pressure range buffer: pressures can be measured at up to 10% outside the pressure range either way, in which case “+Inf” or “-Inf”, as appropriate, will be displayed.
2) Subconn® connectors increase the pressure range to above 30 bar Pressure ranges > 21 bar are only possible without a conductivity sensor.
3) Linearity (best straight line), hysteresis and repeatability.
4) Accuracy and temperature error within the compensated temperature range.
5) Outside the compensated temperature range up to the limits of the operating temperature range, the deviation will be up to twice the value displayed.
6) Temperature information for the pressure sensor (TOB: top of bridge)
7) Power consumption without communication. During the response time (9 ms @ 9600 Baud, 1 ms @ 115’200 Baud), an extra 1…40 mA depending on the line termination.
Resources
Related Equipment
Keller Small Diameter Level Sensor
Keller PR-36 XS Narrow Diameter Sensor for groundwater monitoring. Swiss made. It is ideal for accurate groundwater level monitoring in narrow wells due to it's high accuracy and narrow 16 mm diameter....
Read MoreKeller Surface Level Sensor
Keller PR-46 X Surface Level Sensor for accurate measurement of surface water. This Swiss made sensor combines high precision and reliability. Accuracy as a result of a ceramic measuring cell for low pressure...
Read MoreDFM 6.1 Doppler Flow Meter
The DFM 6.1 Doppler Flow Meter from Pulsar Measurement accurately measures the flow rate of ‘complex’ fluids with suspended solids or entrained air. This clamp-on, ultrasonic non-contacting, flow meter...
Read More